Moon Shot by WilliamAAdams. Inspired by Bre's Moon crater, I thought, why not the whole moon? This thing is a bump mapped sphere that uses the planetary map data/images from here: johnstonsarchive.net/spaceart/cylmaps.html Specifically, I used this one: johnstonsarchive.net/spaceart/moonbumpmap2.jpg I essentially used the same bump mapping technique I used on this bowl: thingiverse.com/thing:13991 That is, use the picture as a height map. Use that height map to displace the vertices around the sphere. Now came the special part. So, I cracked it open, and found that it was in fact hollow! And lastly, since I was exploring the surface using MeshLab, I finally found the man in the moon. This has got to be great for science exploration!
A bit about the .stl files. To generate any spherical thing, you would just change one line of code in the .fab file: local heightsampler = ImageSampler.new({ Filename='moonbumpmap2_720_360.png', Size = size, Resolution = res, MaxHeight=16, }) A newbie's guide to UAVs. What is an amateur UAV? An Unmanned Aerial Vehicle (UAV) is an aircraft that has the capability of autonomous flight, without a pilot in control. Amateur UAVs are non-military and non-commercial.
They typically fly under “recreational” exceptions to FAA regulations on UAVs, so long as the pilots/programmers keep them within tight limits on altitude and distance. Usually the UAV is controlled manually by Radio Control (RC) at take-off and landing, and switched into GPS-guided autonomous mode only at a safe altitude. What do I need to make one? ---1) An RC plane, muticopter (quadcopter/hexacopter/tricopter, etc) or helicopter.
What does DIY Drones have to offer? The DIY Drones community has created the world's first "universal autopilots", ArduPilot Mega (APM) and its next-generation big brother, Pixhawk. A full setup consists of: Pixhawk autopilot: The electronics, including twin processors, gyros, accelerometers, pressure sensors, GPS and more (shown at right). Udrones Store. Drone quadricoptère Parrot AR.Drone - Carène externe Jaune. Google+ Twitter Facebook Youtube Contactez-nous au 05.56.39.37.05 Le Spécialiste Européen de la Robotique de Service Panier : 0 Livraison en 48h Panier (vide) Aucun produit 0,00€ Expédition 0,00€ Taxes 0,00€ Total Les prix sont TTC Panier Commander Ex: Mindstorm, Kit Gadgeteer, Capteur… Bienvenue Identifiez-vous Langues : Catégories Electronique et robotique Robots programmables pour l'éducation Robots grand public Robots pour la recherche Fin de vie Fabricants Produits phares Chassis 6x6 Wild Thumper avec...Châssis robotique 6x6 Wild Thumper pour vos robots d'extérieur...
Pourquoi commander ? Tous nos services Accueil > Robots programmables pour l'éducation>Drônes personnels>AR.Drone 2.0>AR.Drone 2.0 - Carène externe Jaune Agrandir AR.Drone 2.0 - Carène externe Jaune La nouvelle génération arrive ! Avis client 0 En stock En cours de réapprovisionnement Un produit Parrot dont 0,30€ d'éco-participation Ajouter au panier Par rapport à sa version précédente, l'AR.Drone 2.0 apporte les fonctionnalités suivantes: MakerBeam.eu - a miniature T-slot. DE0 Nano VGA Output - Parts List. PyroElectro News, Projects & Tutorials. Kit Prusa Mendel. Price compare 3D printers. DVD Training 12: Blender for 3D Printing - Blender Store. By Dolf (Macouno) Veenvliet. Blender already supports 3D printing modeling and file-formats since 2002. With the latest Blender version (2.67) this now is even more accessible and powerful with the new 3D Printing Toolbox and real-time Mesh Analysis features.
This Training DVD is for everyone who is into 3D printing, beginners and professionals alike. There are extensive chapters introducing Blender modeling for new users. It then handles all topics you need to know for efficient and good quality 3D prints, including color, wall thickness or overhang problems. You will also find printable models to experiment with yourself. Whether you own your own 3D printer, or use online services such as ShapeWays, this 3+ hours training DVD will help you joining this exciting new Maker era! Dolf Veenvliet is a Dutch artist who has been exploring 3D printing for sculpture design for many years. This DVD has been produced by Blender Foundation.
(Click on the image for an example chapter) B9Creator™ | Home | What will YOU create? Aromathérapie Aroma-Zone. Kit robotique Lego MINDSTORMS EV3. Le tout nouveau kit Lego MINDSTORMS EV3 constitue la dernière évolution en date du kit robotique pédagogique Lego Mindstorms. Avec Lego MINDSTORMS EV3, créez votre propre robot qui peut penser, marcher et observer le monde. Grâce à Lego MINDSTORMS EV3, vous êtes libre de construire tous les robots qui vous viennent à l'esprit, en suivant votre imagination. Vous trouverez dans le kit Lego MINDSTORMS EV3 des instructions de montage pour 5 robots et 12 autres manuels officiels se trouvent en ligne.
Donnez vie à votre robot Lego EV3 en utilisant un langage de programmation graphique très simple disponible pour PC et Mac. Connectez vous sur le site de la communauté Mindstorms pour échanger avec d'autre passionnés de Lego Mindstorms et échanger des idées et de l'expérience. Contrôlez votre robot MINDSTORMS EV3 avec la télécommande inclue ou bien avec votre smartphone ou tablette(aplication gratuite pour Android et iOS) ou enfin développez une intelligence autonome pour résoudre vos challenges.
Plating Kits Electroplating Kits Aluminum Anodizing Kits Powder Coating Systems Metal Polishing And Buffing Supplies - Caswell Inc. The Pi Hut | Raspberry Pi Accessories. D60mm PMMA Transparent longueur au choix. :: fabrication et distribution de composants industriels plastiques et métalliques. - | Connexion Demandez votre catalogue gratuit PrevNext Welcome to Essentra Components Caps et Bouchons Noyaux De Ferrite Suppression EMI Scellés De Sécurité, Protection Pour Les Emballages Et Les Roulettes Matériel LED Embouts À Lamelles Et Embouts Enveloppants Pour Tubes, Raccords Entretoises & Colonnettes Verrous, Loquets, Fermetures Et Charnières Guides Carte Et Extracteurs Gestion De La Fibre Protection Hydraulique Et Pneumatique Accessoires Pour Mobilier Joints Profilés, Sauterelles Et Accessoires De Fermeture Supports Anti-Vibration et Paliers A Glissement Accessories Ventilateurs Bandes et Pastilles Adhésives Inscrivez-vous à notre bulletin d'information Demandez votre catalogue gratuit.
Barre PMMA ronde - POLYDIS. Quincaillerie. B9Creator - A High Resolution 3D Printer by Michael Joyce. Color Voting Update - 06/11/12 at 6:11 AM MST The Voting is Over, we have a winner! Black - 32, Blue -11, Clear - 9, Red - 2, Gold - 2, Green - 1 Right from the beginning I wanted the B9Creator to be different. Anodized aluminum construction, stainless steel hardware, many thoughtful features that enhance normal operation... all these things set the B9Creator apart from the DIY 3D Printer herd. But when it comes to printing complex, detailed and fragile objects, this is where the B9Creator really shines bright!
DIY 3D Printers based upon the Fused Deposition Modeling (FDM) concept simply can not match the higher resolution capability of the B9Creator. We utilize a powerful Digital Light Processing (DLP) projector to shine a 1024 x 768 pixel image onto a layer of photo-initiated polymer resin. How about speed? "But how much does that resin cost? " As you will see below, the project development is already well along and is about set for production. So... (Working on resin development) B9Creator Sales. The B9Creator™ can build objects as large as belt buckles or as detailed as a tiny filigree ring, with precision typically possible only on machines costing three to five times as much. In addition, because DLP technology exposes an entire build layer at a time, total build times for most objects is normally between two to five times faster than other comparable technologies.
Another unique advantage of this system is that the output resin, unlike that of photo-polymers in general, is proven to be directly castable when cured properly. The ring (at right) was created in Rhinoceros and printed on the B9Creator, the first of a three-ring set. This promise ring was created with a gap in the design at the top to accommodate the crown of a Claddaugh-type ring that will be the engagement. The B9Creator™ will be initially offered in two versions, as a kit which will require user assembly for US$2,990, and as an assembled machine including some consumables and extra parts for US$4,995. Moteur stirling.
Bricolage. Proxxon MF70 CNC Conversion Kit by ttsalo. First, while printing the motor mounts, it's a good idea to do a google search with "mf70 cnc" and read some of the top results - many people have written better illustrated guides than fits here. Take off the handwheels from the mill. For X- and Y-axis this is done by loosening the nut at the far end of the axis (note! The Y-axis has left-handed threads) and pulling the axis out far enough so that you can punch out the holding pin.
After this, the wheel comes off. Next thing needed is a coupler for each axis. In the original design, the handwheels themselves push against the bearings. X- and Y-axis motor mounts can then be attached. After the mounts are in place, the couplers attached and the axis nuts tightened to take out the play, the NEMA17 motors with 20mm shafts can be mounted with M3x12 screws. If everything still moves smoothly, it's time to hook up the electronics. It's possible to use RepRap electronics. The zipfile contains all the three STLs. Accueil. RC-Machines.
Sehen Sie sich unsere Foto-Gallerien an Seminare mit Charakter Wir wünschen Ihnen frohe Ostern Ebenfalls sind wir am 2 Mai für Sie da Wir werden keine Brücke übers Wochenende machen Unser Katalog.