background preloader

Charger / Controller

Facebook Twitter

Tycon Power Systems Renewable Energy Home. Solar Converters PT 12-3R8, 12V MPPT Charge Controller. Application This charge controller is used to charge a battery from a PV power source.

Solar Converters PT 12-3R8, 12V MPPT Charge Controller

This charge controller can be ordered with a special float voltage to charge small batteries used for Video or digital cameras or small security camera systems. The exceptional small size of this unit makes it extremely portable and able to fit almost anywhere in the user equipment. All the listed Power Trackerâ„¢ charge controllers with MPPT can charge control a battery of lower voltage. Many of these models can also accept battery or multiple input sources. Note: For optimal Maximum Power Point Tracking performance, it is recommended that MPPT charge controllers be used in conjunction with uniform solar arrays consisting of multiple, identical solar panels. Features Special units have a suffix of B XX after the part number. Mechanical Specifications Weight: approx. 0.3 lbs. Note: In the interest of continuous product improvement, specifications subject to change without notice.

Order Model No: Solar Charge Controllers - reeetech. Photovoltaic System Charge Controllers and Linear Current Boosters The charge controller is a necessary part of your power system that charge batteries, whether the power source is PV, wind, hydro, fuel, or utility grid.

Solar Charge Controllers - reeetech

Its purpose is to keep your batteries properly fed and safe for the long term. (PDF 308Kb) A charge controller is an electronic voltage regulator, used in off-grid systems and grid-tie systems with battery backup, that controls the flow of power from the charging source to the battery. The charge controller automatically tapers, stops, or diverts the charge when batteries become fully charged. In off-grid facilities, PV systems are either stand-alone or centralized configurations that serve multiple units. Solar panels charge the battery, and the charge controller insures proper charging of the battery. A charge controller is needed in charging deep cycle lead acid batteries used in Solar PV System. 7 Amp Solar Charge Regulator. 30 Amp Solar Charge Controller. 1.5 Amp Three Stage Onboard Battery Charger/Maintainer. PWM Solar Charge Controllers from Xantrex, Morningstar, Phocos - Morningstar ProStar PS-30M-PG, PWM Solar Charge Controller 30 Amp, 12/24 Volt ,

ProStar PS-30M PWM Charge Controller (30 amp 12V or 24V w/ display & positve ground) This sophisticated line of PV charge controllers incorporates constant voltage PWM to make maximum use of valuable PV power.

PWM Solar Charge Controllers from Xantrex, Morningstar, Phocos - Morningstar ProStar PS-30M-PG, PWM Solar Charge Controller 30 Amp, 12/24 Volt ,

They have automatic equalization, temperature compensation and very high efficiency. They can be used on 12-, 24- and 48-volt systems with sealed, gel and wet-cell lead-acid batteries. Front panel LEDs indicate when the batteries are being charged and relative battery state of charge. Reverse polarity protection on input and output. Morningstar ProStar PS-30M-PG, PWM Charge Controller Includes Digital Meter Rated Solar Current: 30 Amps Rated Load Current: 30 Amps System Voltage: 12/24 Volt Warranty: Five years The "-PG" version of this charge controller has a positive ground.

Adds new features and protections using highly advanced technology Provides longer battery life and improved system performance Sets new standards for reliability and self-diagnostics. ARDUINO SOLAR CHARGE CONTROLLER ( Version 2.0) Parts: 1.Arduino Nano (Amazon / eBay) 2.P-MOSFET ( Amazon / IRF 9540 x2 ) 3.Power diode ( Amazon / MBR 2045 for 10A and IN5402 for 2A) 4.Buck Converter ( Amazon / eBay) or Voltage Regulator (LM7805) 5.Temperature Sensor( Amazon / LM35) 6.Current Sensor ( Amazon / ACS712) 7.TVS diode ( Amazon / P6KE36CA) 8.Transistors ( 2N3904 or 2N2222) 9.Resistors( 100k x 2, 20k x 2,10k x 2,1k x 2, 330ohm x 5)


ARDUINO SOLAR CHARGE CONTROLLER (PWM) [ Play Video ] In my previous instructables I described the details of energy monitoring of a off grid solar system.I have also won the 123D circuits competition for that.You can see this ARDUINO ENERGY METER.


Finally I post my new version-3 charge controller.The new version is more efficient and works with MPPT algorithm. You can see it by clicking the following link.