NANOcopters

Mount Camera Gimbal on Mini Quadcopter - Feiyu Mini3D 3-Axis Review. To do aerial filming it doesn’t have to be a large multicopter, let’s push the limit of mini quad and mount a 3-axis camera gimbal on it, see what we can do.

I chose the Feiyu Mini3D gimbal for this aerial photography platform, because of its small form factor and light weight. Get your Feiyu Mini 3D 3-Axis Camera Gimbal from Banggood. I am quite impressed with the end result. For someone like me who doesn’t have extensive experience in using a camera gimbals, I find this Feiyu Mini 3D gimal really easy to use!

Everything just works out of the box! The stabilization was working great even when it was windy, and my quad wasn’t properly tuned either which wobbles a lot during flight. However I do find just a little yaw vibrations in still shots, and sometimes a slight wobbles in sharp bank turns. I built a 2-axis camera gimbal from scratch before , even though I was using plywood sheet for the frame, and there were only 2 motors, it still weights quite a bit. Related 21st June 2014. 250 grams or less flight weight brushless motor multirotor thread. Discussion 250 grams or less flight weight brushless motor multirotor thread The threshold requiring R/C pilot registration in the U.S. is the outdoor, remotely controlled operation of anything that flies that is over 250 grams in mass.

I specified brushless motors here to avoid a thread filled with a bazillion toy grade suggestions. Suggestions for RTF, kits, and scratch builds wanted here. Aircraft must be available in the U.S. or via very cheap shipping from elsewhere, such as China. SOME of the links below might be over the 250g flight weight limit, especially the 180 size quads. Minpin 115mm Brushless Quad Lisam LS-150 150MM Carbon Fiber Frame D-Mouse - 120mm X Quad Hermit Micro FPV brushless quadcopter 145mm 98g Shendrones Shrieker 130 Deformation Insects 130MM Carbon Fiber Frame Kit Diatone ZMR160 90mm to 145mm Micro Multirotor FPV Build Thread Quanum Wisp 110 Blade 200QX RMRC Hellbender 122 and 204 Hobbico's Elanview Cicada Brushless RTF Drone w/FPV Camera Review.

Projects:crazyradio:protocol - Bitcraze Wiki. The Crazyradio dongle is based on a Nordic semiconductor nRF24LU1 chip.

The radio communication is done using the Nordic “Enhanced ShockBurst™” packet protocol in PTX mode with acknowledge. Variable sized packet, from 1 to 32 bytes, can be send and acknowledged by the copter. The acknowledgement packet can contain a payload from 0 to 32 Bytes. This page documents the protocol used in version 0.52 of the Crazyradio dongle. Future version (up to 1.0) will be kept compatible. Radio configuration Crazyradio is configured in PTX mode. PRX mode One active pipe with the address configured in the Crazyradio dongle, by default it is 0xE7E7E7E7E7 5 byte address Dynamic payload length enable Payload with ack enable The Crazyflie is already configured that way.

USB protocol The USB devices has the VID/PID couple 0x1915/0x7777. Data transfer When the radio dongle is configured to use PTX (emitter) mode it sends a packet to the copter and waits for the acknowledge. Send the packet to EP1_OUT. Set data rate. Bitcraze Crazyflie frame by VGer. v1.7 - See v1.6.5 - This frame is similar to v1.5 with some minor alterations to the motor attachments and thicker/stronger outer rings.

Attach frame to the bottom side of the plastic motor mounts of the Bitcraze Crazyflie quad and fix with foam tape (carefull do not to clip the motor wires). Always Innovating: MeCam. Crazyflie Nano Quadcopter Kit 10-DOF with Crazyradio (BC-CFK-02-A) [ROB01315M] - $179.00. I was just wondering when this product will be in stock again?

Please kindly click " Notify Me " button and you will receive an email when it is in stock Answered by Yang tongtong | 2014-03-14 Was this useful? 0 of 0 people found this useful If I were to cut the arms off of the circuit board, would that damage the functionality of the quadcopter? Just make sure not to "break" them off, since this kind of force might affect the MEMS sensors. Answered by Marcus Eliasson | 2014-03-18 No, it shouldn't since there are no signals routed out onto the arms that holds the motors.

Is this compatible with the JR DSM2/DMSS transmitter? It could be compatible with a transmitter using the Nordic radio chip (like the E-Sky transmitter). What is the best joystick to control a Crazyflie? The best one I've seen is a USB PlayStation 3 controller. Index - Bitcraze Wiki.