KamuiCosplay | Home | Online Store Powered by Storenvy. DIY Macrame Bracelet - Honestly WTF. Growing up by the beach in Southern California, the ability to knot a macrame bracelet was practically a right of passage. Although those days are long behind us, we’ve never forgotten the ever-so-simple square knot technique. This time, however, we’re replacing hemp and wooden beads for more updated elements like colorful nylon cord and glossy metal charms. Happy knotting! You’ll need: Start by cutting the knotting cord into two 30 inch, two 20 inch and one 10 inch lengths. Center the 30 inch cord under the two middle strands.
Pull tightly and slide the knot up to the top. Finish the 2nd half of the square knot by folding the left cord over the middle strands and under the right cord. Pull tightly and repeat the steps – left, right, left, right . . . To finish the knots, thread one of the cords onto a needle and sew up the center of 3-4 knots along the backside. Repeat the same step on the other cord. After sewing up both knotting cords, trim away any excess. DIY Braided Bead Bracelet - Honestly WTF. It’s been awhile since our last bracelet DIY. I don’t know about you, but our wrists have been begging for another colorful addition for months now.
So after playing with some materials that were already on hand, we’ve created a tutorial for a braided bead bracelet, which is a not so distant cousin of the hex nut and wrap bracelet. Because honestly, you can never have too many . . . You’ll need: Cut the waxed linen cord into a 26″ and 19″ piece. Tie a knot about half an inch down from the loops. Start braiding the strands. Push the bead against the base of the braid, and cross the left strand over the middle. Keep a finger at the base of the braid, holding the beads in their place and keeping the braid tight. Finish the bracelet with another inch of braided cord, measuring it against the wrist.
Thread on a two hole button – two strands through one hole and one strand through another. Trim the end. Your bracelet is finished! (all images by HonestlyWTF) DIY: Masquerade Mask (from scratch) DIY Friendship Bracelet - Honestly WTF. For several months now, we’ve been receiving emails requesting a friendship bracelet DIY. Well, friends, ask and you shall receive!
Today, we’ll give you a step by step tutorial on the classic chevron pattern. If you used to whip up friendship bracelets like a champ in grade school and have since forgotten how, consider this a refresher course. And if you can make these with your eyes closed and arms tied . . . umm, can we still be friends? You’ll need:embroidery threada safety pin or tapea pair of scissors Start by cutting several strands of embroidery thread at about 24 inches each. Make sure there are two sets of each color. Start on the left side with the outermost color (shown here in red) and make a forward knot by creating a 4-shape over the 2nd color, loop it under and back through the opening.
Pull up and to the right to tighten. Continue knotting towards the left until the outermost strand reaches the middle. (top image via Jak & Jil, rest of images by Honestly…WTF) Old Mens T-shirt Sewn Into Women's Dolman Tee. My husband and I are runners so we have a million t-shirts. I love transforming these boxy, oversized tees into something I will actually want to wear other then for a nightgown. I love this heather grey and wanted to make it into my favorite style tee. I love the comfortable, effortless style of the dolman tee...
It took me about 15 minutes or so. I played around with seams to get the fit right. Supplies: DIY intructions: Full Video go here (it's old though). Begin by removing the collar of the shirt, pull to create an off the shoulder look. Mark your 1/2 your hip measurement inside the t-shirt so it's even. Pleat about 4 inches up by folding accordion folds and pinning through front and back. Mark your arm hole measurement and pin from the under arm seam to that measurement. When you sew, start at the bottom hem and sew up to the under arm seam in a gradual line. Cut all the excess interior fabric away or serge the interior. Basket Weaving old tshirts.
I love a simple top with a twist. The strips were a bit time consuming because I sewed them together to create a more tailored look. I kept the front plain, but you can flip it to be worn either way... Make strips using similar jersey. I wanted a more tailored look so I cut the strips wide enough, folded them in half (right sides together) and flipped them with a loop turner (you can get this at any fabric/craft store). This is more difficult, but looks nicer.
For an easier DIY you can cut the strips right from the back of the shirt. Weaved them in and out and sew! Once I got to the length I wanted, I made a larger strip to go all the way around. front and back view. I Could Do That - StumbleUpon. Judah Method - Bleaching Experemnet on the Behance Network.