DIY Braided T-Shirt Bracelets - Henry HappenedHenry Happened. DIY / how to make a few bracelets - need twine. Popsicle Stick Bracelets. So I was looking through my vintage craft book collection and ran across a 1970 Pack O’ Fun magazine. They had instructions on how to take a simple popsicle stick and turn it into a bracelet. I’m always happy to try and take a good idea and run with it. Well, I’m certainly on board for that. The thought of being able to make wood pliable put all kinds of ideas in my head.
But we’ll start with the project at hand which happened to be bracelets. So just in time for Easter Baskets, lets put together some cute bracelets. With bling. Are you new to the Sitcom? For this project I used: Popsicle sticks (bought the industrial strength size bag from Walmart because this project might go in future directions)Drinking glass (for forming- use a glass with a top opening that is slightly smaller than you want your bracelet to end up)Emory board or sand paperAcrylic paintStick on jewels (for bling)Mod Podge I then used an emory board to sand them so that all edges and paint surfaces were smooth.
How to Make a Beautiful “Love” Necklace {Giveaway} I’m Kate from Cheap Crafty Mama and I’m so excited to be here to show you how to make this super cool Murano Glass Bead and Freshwater Pearl “Love” Necklace– How to Make a CUTE Necklace Here’s What You’ll Need… • thick silver (or silver-coated) wire • thin silver (or silver-coated) wire • silver chain- cut into 8″ and 6″ sections • 2 beads (I used a murano glass bead and freshwater pearl) • lobster clasp • pliers (round-tipped and needle-nosed) • wire clippers • jewelry hammer (or a hammer with a smooth face) • jewelry hammering block (or thick piece of metal to hammer on) To get started I used the round-tipped pliers to twist the thick wire to spell “love.” When I was done shaping it I hammered it with my jewelry hammer. Next, I made the bead pendants.
Using the thin wire, I made a little loop around the tip of my pliers. I clipped off the extra wire from the end of the loop and then slipped the bead on the long part of the wire, then made another loop on the other side of the bead. DIY Chevron Necklace. Last week Carly at Chic Steals posted her late summer Objects of Desire. I loved this Open Triangle Necklace from ASOS. Normally I wouldn’t DIY a necklace that could be purchased for less than $20, but I already had all of the materials and it only took a few minutes. Remember the nail polish ‘enamel’ necklace? This is the same idea except that I cut the chevron shape out of sheet metal using tin snips. I gave it a couple coats of nail polish and let it dry before using jump rings to attach a brass chain. DIY Chalkboard NecklaceGuest Gal Cat | Henry HappenedHenry Happened. A paint chip necklace. Make a mummy necklace! Hi! It's Monday again! WHEW!! THis month is flying by! Today I am hoping to give you a little inspiration to make a sweet little Halloween necklace!
Here are the top three reasons this project rocks like fraggles: 1. 2. 3. You will have to excuse this flash (GASP) photography. Well, you want to make one dont you?? Here is what you need: Glue A square or rectangle piece of wood from the craft wood section (is that a real thing? And the secret ingredient??? Start by drilling a small hole in the top of the wood. Add some glue to the wood Start wrapping the thread tape around the square. Then keep wrappin' and wrappin... this photo is where I started noticing during the editing process that the little dude has his eyes following me.
Add some glue to the back and kinda sqish it down. Next use a tooth pick to find and poke through the hole you drilled See him looking at me?? Twist the jump ring open. Add the ball chain and you have yourself a mummy necklace! Yeah, he is so strange. Happy Halloween!!!!