DIY Braided Hex Nut Bracelet. We’re nuts for nuts. Is there a more versatile and inexpensive DIY component than a hex nut from the hardware store? You can imagine our excitement when we first discovered Philip Crangi’s Giles & Brother Hex Collection. Honestly, nuts braided into jewelry is WTF genius!
With a few items that we always seem to have lying around, we tackled the technique and made our own spine-like braided hex nut wrap bracelet. You’ll need:3 strands of cotton butcher’s twine cut into one yard pieces18 small brass hex nutsa bit of dexterity! Gather the 3 strands of twine and tie a knot at the top, leaving about 2 inches of slack. Keep your thumb at the base of the braid, holding the nut in its place. Repeat the steps, by threading the rest of the nuts to the outer pieces of twine before they are crossed over. The bracelet should wrap around your wrist at least two or three times. Good luck!! (top image from here, rest of images by Honestly…WTF) DIY Friendship Bracelet. For several months now, we’ve been receiving emails requesting a friendship bracelet DIY.
Well, friends, ask and you shall receive! Today, we’ll give you a step by step tutorial on the classic chevron pattern. If you used to whip up friendship bracelets like a champ in grade school and have since forgotten how, consider this a refresher course. And if you can make these with your eyes closed and arms tied . . . umm, can we still be friends? You’ll need:embroidery threada safety pin or tapea pair of scissors Start by cutting several strands of embroidery thread at about 24 inches each.
Start on the left side with the outermost color (shown here in red) and make a forward knot by creating a 4-shape over the 2nd color, loop it under and back through the opening. Pull up and to the right to tighten. Now pick up the outermost color on the right side (show here in red) and make a backward knot, creating a reverse 4-shape over the 2nd color, loop it under and back through the opening. DIY Wrap Bracelet. You should all know by now that we are all about stacking bracelets on our wrists. The more, the better.
In fact . . . the most, the best! With that being said, we’ll show you how to master a version of the ever so popular wrap bracelet. It’s so simple and addicting, you’ll soon be churning out these wristlets with your eyes closed. Clearly this arm party train isn’t stopping and it’s about time you get on board! You’ll need (for a double wrapped bracelet) :* Lengths will vary depending on the size of your wrist (see comments for suggestions). Fold the length of leather cording in half to form a loop. Place the ball chain along the leather cording with the end of the chain meeting the end of the wrap.
Continue wrapping while checking it for fit around the wrist. When you have reached the end of the ball chain wrap the linen cording around the leather strands 2-3 more times. Thread the hex nut through the strands and tie a second knot. Trim with scissors and your wrap bracelet is finished!! DIY Luv Aj Handpiece. When the lovely Amanda Thomas of Luv Aj offered to show us how to DIY her signature handpiece, we were ecstatic! Not only are we huge fans of her jewelry, we’ve been dying to adorn ourselves with this ring and bracelet combination. Thank you for the awesome tutorial, Amanda! Xx This season, the best seller in the entire collection was the Polished Pyrite Handpiece.
It’s simple, a tad bit edgy, and something you can actually wear all day everyday. Add some bracelets on your wrist, throw on a couple rings, and this little handpiece seems to work in every single scenario. If you DIY, or even if you don’t, it may seem too advanced to make but after my tutorial, you’ll see that it’s really not! You’ll need: Now that you have all you need, let’s get cracking. Now for the bracelet portion- everyone’s wrist is a little different so you can ball park the length. Don’t close the jump ring yet though, we need to add the two longer strands of the thin chain to the same jump ring.
Voila! DIY Braided Bead Bracelet. It’s been awhile since our last bracelet DIY. I don’t know about you, but our wrists have been begging for another colorful addition for months now. So after playing with some materials that were already on hand, we’ve created a tutorial for a braided bead bracelet, which is a not so distant cousin of the hex nut and wrap bracelet. Because honestly, you can never have too many . . . You’ll need: Cut the waxed linen cord into a 26″ and 19″ piece. Tie a knot about half an inch down from the loops. Start braiding the strands. Push the bead against the base of the braid, and cross the left strand over the middle. Keep a finger at the base of the braid, holding the beads in their place and keeping the braid tight.
Finish the bracelet with another inch of braided cord, measuring it against the wrist. Thread on a two hole button – two strands through one hole and one strand through another. Trim the end. Your bracelet is finished! (all images by HonestlyWTF) DIY Embellished Friendship Bracelets. The weather is warming up and my wrists are feeling rather lonely and bare after hiding under long sleeves all season long. But after digging up last year’s DIY friendship bracelets, I realized they desperately needed sparkly and shiny upgrades. Today we’re showing you three easy ways to embellish your friendship bracelets, making them all grown up . . . To add rhinestones, you’ll need:a chevron friendship bracelet (tutorial found here)5-6” crystal rhinestone chain (last used here)1 yard of embroidery flossan embroidery needlea pair of scissors Thread the needle with embroidery floss and tie the end into a double knot. Stitch the floss between the first two rhinestone links, pushing needle out the middle of the bracelet.
Continue stitching between the rhinestone links. Your friendship bracelet is sparkling and finished! To add studs, you’ll need:a chevron friendship bracelet (tutorial found here)5 3/8” brass cone studs (last used here)a pair of small, sharp scissorsa screwdriver. DIY Macrame Bracelet. Growing up by the beach in Southern California, the ability to knot a macrame bracelet was practically a right of passage.
Although those days are long behind us, we’ve never forgotten the ever-so-simple square knot technique. This time, however, we’re replacing hemp and wooden beads for more updated elements like colorful nylon cord and glossy metal charms. Happy knotting! You’ll need: Start by cutting the knotting cord into two 30 inch, two 20 inch and one 10 inch lengths. Fold the 20 inch piece in half, pull the loop through the ring, fold it over the ring, and pull the rest of the cord through the loop. Repeat the step on the other side of the ring. Center the 30 inch cord under the two middle strands. Pull tightly and slide the knot up to the top. Finish the 2nd half of the square knot by folding the left cord over the middle strands and under the right cord. Pull tightly and repeat the steps – left, right, left, right . . . Repeat the same step on the other cord.