Austin DIY Ribbon Microphone Kits - Austin Microphones. The AUSTIN Mic Pre (AMP) Kit is our brand new Do-It-Yourself preamplifier kit designed especially for Austin Ribbon Microphones. No fancy lights, meters, or phantom power... This is a dedicated, world-class ribbon microphone preamplifier that YOU build. The Austin Mic Pre (AMP) is a complete DIY kit with a fully-illustrated step-by step instruction tutorial - just like our Austin Ribbon Microphones - and includes everything down to the hex key for the knob and a static wrist strap for handling the semiconductors. You need a soldering iron, solder and a few basic hand tools like a screwdriver and pliers. Designed with state-of-the-art circuitry, and premium audio components, the Austin Mic Pre (AMP) delivers excellent performance over the entire audio spectrum... and beyond.
Its 6 gain settings range from 42dB to 72dB, and deliver a whisper-quiet -135dBvA EIN, with just .0067% THD+N at +19dBV out. It can be assembled in 3-4 hours. Austin Mic Pre (AMP) Spec Sheet. DIY Central. Info: Your browser does not accept cookies. To put products into your cart and purchase them you need to enable cookies. DIY Central. Drip Electronics.com. OPTO 6 NOW IN STOCK WITH T4'S / contact sales@dripelectronics.comThis e-mail address is being protected from spambots.
You need JavaScript enabled to view it for more information drip would like to thank you for your patience in the development of this release. due to the very important request to have two units in one enclosure , heavy modification to the original ue-100 concept design was necessary . as with the development of the dual ‘crystal’ amplifier . a pristine sounding dual output amplifier and input buffer stage using lundahl audio transformers . the psu was condensed and modified to accommodate the highest quality IXYS rectifiers and thermal management for the highly regulated tube heater power supplies as with the capability to handle the load of two units in operation . heater supplies are separated per channel , the amplifier using it’s own heater power supply for isolation. modification of power interconnection was adapted to use readily available molex cable assemblies . drip.
PAiA Corporation - Analog Synths, Theremins, Preamps, and More. Wiring the Rev A/D/F with Hairball Case - Power. Before starting any wiring, check that the case itself is electrically connected between all panels. The screw holes make a convenient place to insert your probes as they are free of any powder coat. If you find a panel is not making electrical contact with its neighbor, tighten the screws until it does.
Failing that, scrape a bit of paint off between the surfaces that contact each other when the panels are tightened against each other. Don't forget that the top and bottom must also make electrical contact with the sides. Chassis Ground Let's begin with the single most important connection you will make. Look at this picture closely. This connection is crucial to ensuring your safety and the safety of others who come in contact with your project. Start by drilling a hole nearby to the IEC connector itself. Use a star lock washer and nut to secure the screw to the chassis.
Add a solder lug, another star washer and a nut to complete the chassis ground assembly. Power Transformer Types. Drip Electronics.com. Hamptone Home Page. Hairball Audio. March 25th 2014 We are currently out of revision A and D kits. We expect to have more in mid April. Send us an email to be notified when kits arrive. March 9th 2014 We had a large batch of FET kits in last week and they are now sold out. If you would like to be notified when FET kits arrive, send an email to info@hairballaudio.com. Lola kits will be back in stock on March 19th. February 27th 2014 Stock update: First, thank you for your patience.
Lola kits will be back in stock around March 14th. January 29th 2014 We had kits today but they sold out fast. If you would like to be notified when kits arrive, send an email to info@hairballaudio.com. We'll have Lola kits this Friday or Monday. January 28th 2014 Hi All! You may have noticed we've had issues getiing stock. If you would like to be notified when kits arrive, send an email to info@hairballaudio.com. December 8th 2013 You may have noticed most of our kits are out of stock (thank you!). We are currently out of FET Compressor kits. July 3rd 2013. JLM Audio Shop. Great samples of our TG500 mic pre done by Joe Barresi with guitarist Luis Maldonado now on our SoundCloud page here Joe Barresi mentions on Pensado's Place that his current favorite compressor is the JLM Audio FC500 FET Compressor.
Click on photo below or this link to go to youtube to watch Air Mail now has online tracking to USA, Canada, UK, Germany, Ireland, Spain, China, Singapore & New Zealand. Free worldwide shipping with tracking on all orders $1990AUD or more. This website is best experienced with Internet Explorer or Firefox Australian Orders will have 10% GST added at checkout.